null

Hand Tools

Hand Tools

  • THREAD CUTTER 16TPI C/W HANDLE SORBY
    Add to Cart

    Robert Sorby

    THREAD CUTTER 16TPI C/W HANDLE SORBY

    CAD $123.99
    Thread Cutter - 16TPI Cutting tools have been produced in 10, 16 and 20 thread per inch, with a unique, enhanced helix angle specially designed for use in wood to compliment these excellent tools. A Relief Cutting Tool Support Rest makes...
    890H16
    CAD $123.99
    Add to Cart
  • HOLLOWING TOOL 20IN. L 12IN. HL SORBY
    Add to Cart

    Robert Sorby

    HOLLOWING TOOL 20IN. L 12IN. HL SORBY

    CAD $77.99
    Hollowing Tool 20" By Robert Sorby H.S.S. Designed specifically for those who wish to make hollow forms or vases Handle length: 12" Replacement Cutter model 851C
    855H
    CAD $77.99
    Add to Cart
  • CHISEL GOUGES ROUGHING OUT 1 1/4IN. SORBY
    Add to Cart

    Robert Sorby

    CHISEL GOUGES ROUGHING OUT 1 1/4IN. SORBY

    CAD $161.99
    1 1/4'' Roughing Out Gouge By Robert Sorby H.S.S. An essential tool for between centre (spindle) work. This tool will quickly turn down square timber to round. The nose being ground square across, allows all the edge to be utilized. All roughing out...
    843LH114
    CAD $161.99
    Add to Cart
  • CHISEL ROUGHING GOUGE OUT 3/4IN.
    Add to Cart

    Robert Sorby

    CHISEL ROUGHING GOUGE OUT 3/4IN.

    CAD $113.99
    3/4'' Roughing Out Gouge An essential tool for between centre (spindle) work. This tool will quickly turn down square timber to round. The nose being ground square across, allows all the edge to be utilized. All roughing out to spindle work can be...
    843H34
    CAD $113.99
    Add to Cart
  • GOUGE BOWL FINGERNAIL LONG HANDLE 3/8IN.
    Add to Cart

    Robert Sorby

    GOUGE BOWL FINGERNAIL LONG HANDLE 3/8IN.

    CAD $113.99
    Fingernail Profile Gouges 3/8" Bowl Gouge (Long Handle) There is difficulty in achieving this profile. Robert Sorby offers a selection of gouges with a factory ground fingernail profile, which is not only safe in use, but also allows the turner to...
    842FLH38
    CAD $113.99
    Add to Cart
  • GOUGE BOWL FINGERNAIL LONG HANDLE 1/2IN.
    Add to Cart

    Robert Sorby

    GOUGE BOWL FINGERNAIL LONG HANDLE 1/2IN.

    CAD $139.99
    842FLH12 Bowl Gouge by Robert Sorby- 1/2" - 23" Length Deep fluted to allow heavy cuts to be taken. This tool is used over on its side (about 15-20m off the vertical) with the flute pointing in the direction of the cut. It is important to let the...
    842FLH12
    CAD $139.99
    Add to Cart
  • GOUGE SPINDLE FINGERNAIL 3/8IN. SORBY
    Add to Cart

    Robert Sorby

    GOUGE SPINDLE FINGERNAIL 3/8IN. SORBY

    CAD $63.99
    Fingernail Profile Gouges - 3/8" - Spindle Gouge (Regular Handle) There is difficulty in achieving this profile. Robert Sorby offers a selection of gouges with a factory ground finger-nail profile, which is not only safe in use, but also allows the...
    840FH38
    CAD $63.99
    Add to Cart
  • GOUGE SPINDLE FINGERNAIL 1/2IN. SORBY
    Add to Cart

    Robert Sorby

    GOUGE SPINDLE FINGERNAIL 1/2IN. SORBY

    CAD $75.99
    Fingernail Profile Gouges - 1/2" - Spindle Gouge (Regular Handle) There is difficulty in achieving this profile. Robert Sorby offers a selection of gouges with a factory ground finger-nail profile, which is not only safe in use, but also allows the...
    840FH12
    CAD $75.99
    Add to Cart
  • CHISEL BEAD FORMING 3/16 H.S.S. SORBY
    Add to Cart

    Robert Sorby

    CHISEL BEAD FORMING 3/16 H.S.S. SORBY

    CAD $49.99
    3/16" H.S.S Bead Forming Chisel - Robert Sorby These tools provide the means of forming perfect beads from 1/8" to 1/2". The nose design permits multiple beads to be cut with precision on spindle for faceplate work. Slight movement of the...
    835H316
    CAD $49.99
    Add to Cart
  • CHISEL BEAD FORMING 1/8IN. H.S.S. SORBY
    Add to Cart

    Robert Sorby

    CHISEL BEAD FORMING 1/8IN. H.S.S. SORBY

    CAD $50.99
    835H18 1/8" H.S.S Bead Forming Chisel - Robert Sorby These tools provide the means of forming perfect beads from 1/8" to 1/2". The nose design permits multiple beads to be cut with precision on spindle for faceplate work. Slight movement...
    835H18
    CAD $50.99
    Add to Cart
  • PARTING TOOL 2MM FLUTED SORBY
    Pre-Order Now

    Robert Sorby

    PARTING TOOL 2MM FLUTED SORBY

    CAD $99.99
    2 mm Parting Tool Fluted 18" long Used with flute downwards. This tool gives an exceptionally good finish even when parting through end grain. Sides taper ground for clearance. High Speed Steel
    832H2M
    CAD $99.99
    Pre-Order Now
  • WOODTURNING TOOLS CURVED SCRAPER SORBY
    Add to Cart

    Robert Sorby

    WOODTURNING TOOLS CURVED SCRAPER SORBY

    CAD $93.99
    Curved Scraper - Robert Sorby The curved end profile makes this excellent for creating, smoothing and blending curved surfaces in bowl and spindle work, eg round bottomed boxes. This new tool is able to take an aggressive cut, whilst retaining...
    828H
    CAD $93.99
    Add to Cart
  • CHISEL TRNG 8PC SET BOWL AND SPNDL SORBY
    Add to Cart

    CHISEL TRNG 8PC SET BOWL AND SPNDL SORBY

    CAD $636.99
    82HS Professional Wood Turning Chisel Set Standard set of 8pc: 1 - 3/4" Roughing Gouge 1 - 1/4'' Spindle Gouge 1 - 1/2" Spindle Gouge 1 - 3/8" Bowl Gouge 1 - 1/2" Round Nose Scraper 1 - 1" Square Nose Scraper 1 - 3/4" Skew Chisel 1- 3-16" Parting...
    82HS
    CAD $636.99
    Add to Cart
  • CHISEL WOODTURNING TOOL 5PC SET SORBY
    Add to Cart

    CHISEL WOODTURNING TOOL 5PC SET SORBY

    CAD $310.99
    52HS Professional Wood Turning Chisel Set Standard set of 5pcs 1 - 3/4'' Roughing Gouge 1 - 3/8'' Spindle Gouge 1 - 1/2" Round Nose Scraper 1 - 1/2" Skew Chisel 1 - 1/8'' Parting Tool Approx. Length: 14'' Overall Length
    52HS
    CAD $310.99
    Add to Cart
  • CHUCK 5IN. 3 JAW
    Add to Cart

    CHUCK 5IN. 3 JAW

    CAD $155.00
    Lathe Chucks - 5" - 4.7kg. These chucks are suitable for toolrooms and production work. The chuck bodies are made of steel and the scroll plates are made of high quality heat-treated carbon steel. These chucks are of plain back design and may be fitted...
    440510
    CAD $155.00
    Add to Cart
  • CHUCK 3IN. 3 JAW
    Add to Cart

    CHUCK 3IN. 3 JAW

    CAD $145.00
    Lathe Chucks - 3" - 1.7kg. These chucks are suitable for toolrooms and production work. The chuck bodies are made of steel and the scroll plates are made of high quality heat-treated carbon steel. These chucks are of plain back design and may be fitted...
    440504
    CAD $145.00
    Add to Cart
  • SAND MASTER 11 1/2IN. OA LENGTH SORBY
    Add to Cart

    SAND MASTER 11 1/2IN. OA LENGTH SORBY

    CAD $98.99
    410 Sand Master - ROBERT SORBY To put a fine finish on turning work and eliminate sanding lines. Velcro 2" sponge pad mounted on phosphor bronze bearing gives excellent service. Total Length: 11-1/2" Handle: 8-1/2"
    410
    CAD $98.99
    Add to Cart
  • CHISEL PEN TURNING SET 3 PC SORBY
    Add to Cart

    Robert Sorby

    CHISEL PEN TURNING SET 3 PC SORBY

    CAD $141.99
    High Speed Steel 3 pc Pen Turning Set Set Contains: -5 /16" roughing gouge, (model # 866H) -1/16" parting tool, (model # 865H) -1 /2" spindle master, (model # 879H) (All chisels are 10" long)
    36HS
    CAD $141.99
    Add to Cart
  • TALON CHUCK
    Add to Cart

    ONEWAY

    TALON CHUCK

    CAD $249.00
    2985 Talon Chuck - Oneway  The Talon chuck is designed for wood lathes with a swing of 16" or less. The chuck body is 3-1/2" and is operated with the use of a key. This will give the operator solid holding power and one-handed operation...
    2985
    CAD $249.00
    Add to Cart
  • ONE WAY STRONGHOLD CHUCK KIT
    Add to Cart

    ONEWAY

    ONE WAY STRONGHOLD CHUCK KIT

    CAD $319.00
    2137 One Way Stronghold Chucks are a heavy duty chuck that is designed for large lathes (16" swing or greater) to provide maximum gripping power. The body diameter of this chuck is 4½" (the largest currently available in our chuck family). The...
    2137
    CAD $319.00
    Add to Cart
  • DOVETAIL PULL SAW IRWIN
    Add to Cart

    Irwin

    DOVETAIL PULL SAW IRWIN

    CAD $25.99
    IRWIN Dovetail Pull Saw The IRWIN 213104 Dovetail is ideal for flush cutting dowels & any fine detail work. The dovetail saw is also a great tool for cutting shims. The pull stroke action eliminates binding and facilitates a straight cut. The...
    213104
    CAD $25.99
    Add to Cart
  • 1 1/4IN. DISH CARVING BIT 1/2IN. SHANK
    Add to Cart

    Craftex Blue Tornado

    1 1/4IN. DISH CARVING BIT 1/2IN. SHANK

    CAD $26.99
    This bit is what you need to make a recessed area that you would find on a tray or signs with raised lettering. Ideal for making trays, coasters, raised letter signs and more. SPECIFICATIONS Diameter: 1-1/4" Cutting Length: 5/8" Radius: 1/4" Shank...
    197318
    CAD $26.99
    Add to Cart
  • SCRAPER CABINET 6IN. SORBY
    Add to Cart

    SCRAPER CABINET 6IN. SORBY

    CAD $13.99
    Cabinet Scrapers - "Robert Sorby" Rect. 6" x 3" Made of the finest steel. Cabinet scrapers, when properly sharpened and burnished produce a finish not available with either a plane or sandpaper. Invaluable to the cabinetmaker.
    1606
    CAD $13.99
    Add to Cart
  • HINGE MORTISE KIT MILESCRAFT
    Add to Cart

    Milescraft

    HINGE MORTISE KIT MILESCRAFT

    CAD $29.99
    Hinge Mortise Kit - MilesCraft This kit allows you to cut accurate door and jamb hinge mortises without any tear or a hole on the wall. The centered tape measures tabs for accurate placement on the door and jamb and the door thickness selector is easily...
    1214
    CAD $29.99
    Add to Cart
  • ABRASIVE KIT SLOTTED FOR WS3000
    Add to Cart

    WorkSharp

    ABRASIVE KIT SLOTTED FOR WS3000

    CAD $19.95
    Slotted Abrasive Kit for WS3000, work Sharp For use with Edge Vision Slotted Wheel (Model # WS30004) only 1 piece P80 PSA (Pressure Sensitive Adhesive) Abrasive; 150mm diameter, slotted 2 pieces P400 PSA Abrasive; 150mm diameter, slotted 2 pieces P1200...
    WS30008
    CAD $19.95
    Add to Cart
  • ABRASIVE KIT HONING FOR WS3000 AND WS2000
    Add to Cart

    WorkSharp

    ABRASIVE KIT HONING FOR WS3000

    CAD $19.95
    Honing Abrasive Kit for WS3000, Work Sharp For use with Tempered Glass Wheel (Model # WS30003) 1 piece 3600 Micro-Mesh PSA Abrasive (equivalent to 6 æ micron); 150mm diameter 1 piece 6000 Micro-Mesh PSA Abrasive (equivalent to 2æ micron);...
    WS30007
    CAD $19.95
    Add to Cart
  • ABRASIVE KIT FINE FOR WS3000 AND WS2000
    Add to Cart

    WorkSharp

    ABRASIVE KIT FINE FOR WS3000 AND WS2000

    CAD $19.95
    Fine Abrasive Kit for WS3000 & WS2000, Work Sharp 4 pieces P400 PSA (Pressure Sensitive Adhesive) Aluminum Oxide Abrasive; 150mm diameter 6 pieces P1000 PSA Aluminum Oxide Abrasive; 150mm diameter 2 pieces P400 PSA Ceramic Oxide Abrasive; 2 in...
    WS30006
    CAD $19.95
    Add to Cart
  • ABRASIVE KIT COARSE FOR WS3000 AND WS2000
    Add to Cart

    WorkSharp

    ABRASIVE KIT COARSE FOR WS3000 AND WS2000

    CAD $19.95
    Coarse Abrasive Kit for WS3000 & WS2000, Work Sharp 2 pieces P80 PSA (Pressure Sensitive Adhesive) Ceramic Oxide Abrasive; 150mm 2 pieces P120 PSA Ceramic Oxide Abrasive; 150mm diameter 3 pieces P220 PSA Aluminum Oxide Abrasive; 150mm diameter 2...
    WS30005
    CAD $19.95
    Add to Cart
  • TEMPERED GLASS WHEEL FOR WS3000
    Add to Cart

    WorkSharp

    TEMPERED GLASS WHEEL FOR WS3000

    CAD $26.95
    150mm Tempered Glass Wheel for WS3000, Work Sharp It replaces the tempered glass wheel with maximum operating speed of 650 RPM that comes with WS3000 or you can apply different grits of PSA abrasives on it to expand the capacity of your sharpening...
    WS30003
    CAD $26.95
    Add to Cart
  • LEATHER HONE KIT FOR WS3000
    Add to Cart

    WorkSharp

    LEATHER HONE KIT FOR WS3000

    CAD $39.95
    Leather Hone Kit for WS3000, Work Sharp For use with WS3000 and allows you to hone for a superior mirror finish. The kit includes: 150 mm tempered glass wheel Adhesive Backed Leather Strop Disk Chromium Oxide Honing Compound Leather Conditioner (white...
    WS30002
    CAD $39.95
    Add to Cart
  • DIGITAL READOUT FOR PLANERS WIXEY
    Add to Cart

    Wixey Digital

    DIGITAL READOUT FOR PLANERS WIXEY

    CAD $119.00
    WIXEY DIGITAL READOUT IMPROVED VERSION The Wixey Planer Digital Readout model WR510 has a new angled display for easy viewing as well as "auto shut off." And like the WR500, it fits most portable woodworking planers. It easily mounts to Craftex,...
    WR510
    CAD $119.00
    Add to Cart
  • TTRACK PLUS 48IN. W/ADJ. LEXAN SCAL INCRA
    Add to Cart

    Incra

    TTRACK PLUS 48IN. W/ADJ. LEXAN SCAL INCRA

    CAD $32.99
    Locate ANY cut on ANY machine EXACTLY where you want it.Lengths of INCRA Track fence without the incremental Shop Stop are an inexpensive way to add a sturdy, basic fence to jigs or miter gauges, but they're also ideal for expanding an existing INCRA...
    TTRACKPLUS48
    CAD $32.99
    Add to Cart
  • TTRACK PLUS 36IN. W/ADJ. LEXAN SCAL INCRA
    Add to Cart

    Incra

    TTRACK PLUS 36IN. W/ADJ. LEXAN SCAL INCRA

    CAD $24.99
    Locate ANY cut on ANY machine EXACTLY where you want it.Lengths of INCRA Track fence without the incremental Shop Stop are an inexpensive way to add a sturdy, basic fence to jigs or miter gauges, but they're also ideal for expanding an existing INCRA...
    TTRACKPLUS36
    CAD $24.99
    Add to Cart
  • TTRACK PLUS 24IN. W/ADJ. LEXAN SCAL INCRA
    Add to Cart

    Incra

    TTRACK PLUS 24IN. W/ADJ. LEXAN SCAL INCRA

    CAD $20.99
    Locate ANY cut on ANY machine EXACTLY where you want it.Lengths of INCRA Track fence without the incremental Shop Stop are an inexpensive way to add a sturdy, basic fence to jigs or miter gauges, but they're also ideal for expanding an existing INCRA...
    TTRACKPLUS24
    CAD $20.99
    Add to Cart
  • SMOOTHING PLANE NO. 4 9 3/4IN. LONG
    Add to Cart

    Groz

    SMOOTHING PLANE NO. 4 9 3/4IN. LONG

    CAD $63.99
    9 3/4" Smoothing Plane - GROZ Constructed with fine-grained cast iron and sculptured wood hand rests. The 2" plane iron of high quality steel is easily adjusted and securely held for the best in hand planing. A life time product for the wood craftsman...
    SP4
    CAD $63.99
    Add to Cart
  • POCKET SCREWS 1 1/4IN. NO. 7 FINE W/H.500CT (SMLF125500)
    Add to Cart

    Kreg

    POCKET SCREWS 1 1/4IN. NO. 7 FINE W/H.500CT

    CAD $29.99
    This 1 1/4" fine thread, #2 square drive pan head screw works well in 1/2" thick, hardwood material such as oak, maple, hickory, cherry and walnut. The deep recess, pan head of this screw provides excellent driver engagement and is popular in framing...
    SMLF125500
    CAD $29.99
    Add to Cart
  • POCKET SCREWS 2IN. NO. 8 COARSE W/H 50CT KREG
    Add to Cart

    Kreg

    POCKET SCREWS 2IN. NO. 8 COARSE W/H 50CT KREG

    CAD $5.99
    This 2-1/2-inch coarse thread, #2 square drive washer-head screw works well in 1-1/2-inch-thick material. The washer head of this screw is our most popular head style as the wide bearing surface of the head will not overdrive in the bottom of the pocket...
    SMLC250
    CAD $5.99
    Add to Cart
  • POCKET SCREWS 2IN. NO. 8 CRSE W/H 250CT KREG
    Add to Cart

    Kreg

    POCKET SCREWS 2IN. NO. 8 CRSE W/H 250CT KREG

    CAD $22.99
    This 2" coarse thread, #2 square drive washer head screw works well in softer material. The washer head of this screw is our most popular head style as the wide bearing surface of the head will not overdrive in the bottom of the pocket. This is...
    SMLC2250
    CAD $22.99
    Add to Cart
  • POCKET SCREW 1 1/4IN. NO. 8 COARSE 500PC KREG
    Add to Cart

    Kreg

    POCKET SCREW 1 1/4IN. NO. 8 COARSE 500PC KREG

    CAD $29.99
    1-1/4'' Coarse Thread self-tapping screws are specially designed for pocket hole joinery. They feature a self-tapping auger point that eliminates pre-drilling and a flat head that seats flushly in the bottom of the pocket hole. All of our screws utilize...
    SMLC125500
    CAD $29.99
    Add to Cart
  • PRECISION MARKING RULE 12IN. INCRA
    Add to Cart

    Incra

    PRECISION MARKING RULE 12IN. INCRA

    CAD $20.99
    INCRA PRECISION MARKING RULE 12" Select the proper slot or hole, insert a .5mm mechanical pencil, and mark the measurement with dead-on accuracy. Micro-fine guide holes and slots at every 1/16"and 1/32" scale position instantly locate your sharp pencil...
    RULE12
    CAD $20.99
    Add to Cart
  • PRECISION MARKING RULE 6IN. INCRA
    Add to Cart

    Incra

    PRECISION MARKING RULE 6IN. INCRA

    CAD $10.99
    INCRA PRECISION MARKING RULE 6" Select the proper slot or hole, insert a .5mm mechanical pencil, and mark the measurement with dead-on accuracy. Micro-fine guide holes and slots at every 1/16"and 1/32" scale position instantly locate your sharp pencil...
    RULE06
    CAD $10.99
    Add to Cart
  • SPONGE PADS 2IN. DIA SORBY
    Add to Cart

    SPONGE PADS 2IN. DIA SORBY

    CAD $24.99
    2" Velcro Sanding Pad By Robert Sorby May be used with the "Sand Master" or separately Available - 2" Velcro Sponge Discs - 10 Per Pack Model Grit RS412A60 60 RS412A120 120 RS412A180 180 RS412A240 240
    RS412
    CAD $24.99
    Add to Cart
  • HOLLOWMASTER 3/4IN. SHANK SORBY
    Add to Cart

    Robert Sorby

    HOLLOWMASTER 3/4IN. SHANK SORBY

    CAD $138.99
    by "Robert Sorby" of England Hollow Master 3pc Set H.S.S. A full 3/4" surface gives ample support and prevents the tool from turning over Comes with a swiveling hollowing cutter and a full round scraper cutter Total length: 21" RS230C Replacement...
    RS230KT
    CAD $138.99
    Add to Cart
  • FEATHER BOARD TWIN PACK KREG
    Add to Cart

    Kreg

    FEATHER BOARD TWIN PACK KREG

    CAD $44.99
    KREG Feather Board Twin Pack The True-FLEXO Feather Board gets its name from the careful engineering that went into its design. Many featherboards on the market today apply too much pressure or not enough pressure to the workpiece, resulting in...
    PRS3020
    CAD $44.99
    Add to Cart
  • MITRE GAUGE V27 INCRA
    Add to Cart

    Incra

    MITRE GAUGE V27 INCRA

    CAD $102.99
    INCRA MITER GAUGE V27 The NEW Incra Miter V27 is engineered to provide a high performance, yet low cost upgrade for your Table Saw, Band Saw, Router Table, Disk Sander, Belt Sander or any other tool in need of a better miter gauge. Like all Incra Miter...
    MITER27
    CAD $102.99
    Add to Cart
  • MITRE GAUGE 1000 INCRA
    Add to Cart

    Incra

    MITRE GAUGE 1000 INCRA

    CAD $219.00
    MITER100018T INCRA MITER GAUGE 1000 If you are looking for a great combination of basic affordability combined with unbeaten accuracy, the INCRA Miter 1000 is a terrific choice. We combined a solid-steel laser cut protractor head with a gold anodized...
    MITER100018T
    CAD $219.00
    Add to Cart
  • MITRE GAUGE 1000SE INCRA
    Add to Cart

    Incra

    MITRE GAUGE 1000SE INCRA

    CAD $286.00
    MITER1000SE INCRA MITER GAUGE SPECIAL EDITION The Miter 1000 Special Edition builds on the excellent foundation provided by the Miter 1000. The Incra exclusive AngleLOCK Indexing System delivers 41 lock solid angle stops in 5-degree increments over a...
    MITER1000SE
    CAD $286.00
    Add to Cart
  • MITER GAUGE 1000HD WITH 18IN. TO 30IN.
    Add to Cart

    Incra

    MITER GAUGE TELESCOPING FENCE 18IN. TO 31IN.

    CAD $332.00
    MITER1000HD Miter Gauge 1000 High Definition - INCRA The NEW INCRA Miter 1000HD is the most refined model yet in the Miter 1000 series. The HD stands for High Definition; because the protractor plate's exclusive AngleLOCK Indexing System has a...
    MITER1000HD
    CAD $332.00
    Add to Cart
  • MITER GAUGE WITH 120 ANGLELOCK STOPS
    Add to Cart

    Incra

    MITER GAUGE WITH 120 ANGLELOCK STOPS

    CAD $156.99
    Miter Gauge V120 - INCRA The NEW Miter V120 puts high-resolution, repeatable accuracy within the budget of every woodworkers. An incredible 120 angle stops are laser cut into the steel protractor, with a stop available for every whole degree and two...
    MITERV120
    CAD $156.99
    Add to Cart
  • MITER EXPRESS INCRA
    Add to Cart

    Incra

    MITER EXPRESS INCRA

    CAD $259.00
    MITEREXPRESS INCRA MITER GAUGE EXPRESS The NEW Incra Miter Express Makes Safe and Easy Mitered Cuts Incra's new Miter Express offers any miter gauge owner the safest and most accurate cross-cutting and mitering platform available. Turn any miter...
    MITEREXPRESS
    CAD $259.00
    Add to Cart
  • PRECISION TRAK AND STOP KIT KREG
    Add to Cart

    Kreg

    PRECISION TRAK AND STOP KIT KREG

    CAD $220.00
    KREG PRECISON TRAK & STOP KIT Cutting wood with accuracy is an important part of making sure the project turns out just right. The inaccuracy of pencil marks on a board can then be compounded by the need to follow that mark precisely with the saw...
    KMS8000
    CAD $220.00
    Add to Cart
  • MEASURING TAPE 12FT SELF ADHESIVE L R RDNG
    Add to Cart

    Kreg

    MEASURING TAPE 12FT SELF ADHESIVE L R RDNG

    CAD $16.99
    KMS7724 1/2" Wide Self Adhesive Measuring Tape - KREG TOOLS This 1/2" wide self adhesive measuring tape fits into the indentation on the top side of the Kreg Top Trak and Heavy Duty Track aluminum extrusions. Since the tape has self adhesive backing,...
    KMS7724
    CAD $16.99
    Add to Cart
  • MEASURING TAPE 12FT SELF ADHESIVE R L RDNG
    Add to Cart

    Kreg

    MEASURING TAPE 12FT SELF ADHESIVE R L RDNG

    CAD $16.99
    KMS7723 1/2" Wide Self Adhesive Measuring Tape - KREG TOOLS This 1/2" wide self adhesive measuring tape fits into the indentation on the top side of the Kreg Top Trak and Heavy Duty Track aluminum extrusions. Since the tape has self adhesive backing,...
    KMS7723
    CAD $16.99
    Add to Cart
  • MITRE SLIDE 24IN. INCRA
    Add to Cart

    Incra

    MITRE SLIDE 24IN. INCRA

    CAD $39.99
    INCRA MITER SLIDER 24" This long aluminum runner adjusts from the TOP for perfect sliding action in any standard 3/4" x 3/8" miter gauge slot. Won't warp, shrink, or swell like wooden runners. - A simple turn of a screw adjust Miter Slider for ZERO...
    IMS2
    CAD $39.99
    Add to Cart
  • MITRE SLIDE 18IN. INCRA
    Add to Cart

    Incra

    MITRE SLIDE 18IN. INCRA

    CAD $31.99
    INCRA MITER SLIDER 18" This long aluminum runner adjusts from the TOP for perfect sliding action in any standard 3/4" x 3/8" miter gauge slot. Won't warp, shrink, or swell like wooden runners. - A simple turn of a screw adjust Miter Slider for ZERO...
    IMS1
    CAD $31.99
    Add to Cart
  • GUAGE INCRA
    Add to Cart

    Incra

    GUAGE INCRA

    CAD $23.99
    INCRA Gauge Works as a precision marking gauge, a freestanding depth-of-cut gauge, a fence alignment gauge and a center finder. This easy to use gauge will offer dozens of uses in your projects and become an indispensable layout tool for your workshop.
    IG32
    CAD $23.99
    Add to Cart
  • DRILL DOCTOR SHARPENING 750X KIT
    Add to Cart

    WorkSharp

    DRILL DOCTOR SHARPENING 750X KIT

    CAD $235.00
    Drill Bit Sharpening Kit - Drill Doctor This drill bit sharpener is designed for durability and has the flexibility required sharpening the largest range of dull or broken bits-including split points and masonry bits. With this tool you can sharp bits...
    DD750X
    CAD $235.00
    Add to Cart
  • MORTISING ATTACHMENT KIT
    Add to Cart

    Craftex

    MORTISING ATTACHMENT KIT CT132

    CAD $109.00
    If you don't cut mortises all that often and have a drill press, then this tool is just what you need. This mortising attachment and chisel set for your drill press allows you to double-task a machine you likely already have. Made from cast iron and...
    CT132
    CAD $109.00
    Add to Cart
  • TENONING JIG CRAFTEX
    Add to Cart

    Craftex

    TENONING JIG CRAFTEX

    CAD $169.00
    Super Tenon Jig All cast iron to fit any 3/4" table slot with adjusters for fit Screw clamping to 5" clamping plate with adjustment to 20 degree from vertical 45 degree fence to allow compound angles Micro adjustment Two handles for control Designed to...
    CT084
    CAD $169.00
    Add to Cart
  • SAW STEP GAUGE
    Add to Cart

    SAW STEP GAUGE

    CAD $9.99
    Saw Step Gauge Heavy Gauge Aluminum Our step gauge gives you an exact setting, the first time, regardless of width or set of the blade. More accurate than any ruler. It will set your rip fence, your radial or table saw depth of cut and measure groove...
    B897
    CAD $9.99
    Add to Cart
  • HONING GUIDE
    Add to Cart

    HONING GUIDE

    CAD $18.99
    Honing Guide This easy to use tool enables even an amateur to achieve a perfect edge when resharpening both wood chisels and plane irons Capacity: 1/8" to 2 5/8"
    B775
    CAD $18.99
    Add to Cart
  • HEX KEY WRENCH SET IN. TIN. HANDLE METRIC
    Add to Cart

    HEX KEY WRENCH SET IN. TIN. HANDLE METRIC

    CAD $12.99
    B761 Hex Key Wrench Sets Excellent Quality Made of specially selected steels of either chrome vanadium steel or carbon steel Manufactured to precise standards Heat treated Assures maximum resistance to torque stresses All these keys meet the American...
    B761
    CAD $12.99
    Add to Cart
  • FILE MILL BASTARD 8IN.
    Add to Cart

    Wood Miller

    FILE MILL BASTARD 8IN.

    CAD $11.99
    American Pattern File Type: 8" Mill Bastard This file is made from the finest grade steel and is specially finished by a method designed to improve its cutting efficiency and lengthen its effective life. Picture Differs Slightly
    B662MB8
    CAD $11.99
    Add to Cart
  • FILE MILL BASTARD 10IN.
    Add to Cart

    Wood Miller

    FILE MILL BASTARD 10IN.

    CAD $12.99
    American Pattern File Type: 10" Mill Bastard This file is made from the finest grade steel and is specially finished by a method designed to improve its cutting efficiency and lengthen its effective life. Picture Differs Slightly
    B662MB1
    CAD $12.99
    Add to Cart
  • THICKNESS GAUGE 26 LEAVES
    Add to Cart

    THICKNESS GAUGE 26 LEAVES

    CAD $7.99
    B622 Thickness Gauage 26 leaf thickness gauge. Each leaf is marked. Leaves from .0015” to .025”Edge of each leaf is round and approximately 3 3/8” long. High quality tempered steel, and made to close tolerances.
    B622
    CAD $7.99
    Add to Cart
  • CENTRE PUNCH AUTOMATIC
    Add to Cart

    Groz

    CENTRE PUNCH AUTOMATIC

    CAD $14.99
    Automatic Centre Punch Pressure can be varied from 5lbs. to 30lbs.approximately simply by rotating knurled head. Used for light to heavy marking. Speeds up layout. Overall length 5”.
    B597
    CAD $14.99
    Add to Cart
  • SCREW PITCH GAUGE TP14 42
    Add to Cart

    SCREW PITCH GAUGE TP14 42

    CAD $18.99
    Screw Pitch Gauges Features Made of tempered steel and are precision ground T.P.I. stamped on each blade All blades can be locked to any desired position Number of blades: 30 TPI: 4-42
    B576
    CAD $18.99
    Add to Cart
  • DIAL INDICATOR TYPE A1 921 1IN. TRAVEL
    Add to Cart

    DIAL INDICATOR TYPE A1 921 1IN. TRAVEL

    CAD $24.99
    Dial Indicator 2" Dia. Face - 1" Travel These dial gauges fit all standard magneticc basesSatin chrome-plated case Easy-to-read faces .001" reading Precision ground hard chrome-plated stem and contact point
    B444
    CAD $24.99
    Add to Cart
  • DIAL INDICATOR TYPE A1 911 1/2IN. TRAVEL
    Add to Cart

    DIAL INDICATOR TYPE A1 911 1/2IN. TRAVEL

    CAD $24.99
    Dial Indicator 2" Dia. Face - 1/2" Travel These dial gauges fit all standard magneticc bases| Satin chrome-plated case Easy-to-read faces .001" reading Precision ground hard chrome-plated stem and contact point
    B443
    CAD $24.99
    Add to Cart
  • MINI MAG W/FINE ADJ.
    Pre-Order Now

    Groz

    MINI MAG W/FINE ADJ.

    CAD $13.99
    Mini Magnetic Base - 5" This model comes with a fine adjustment. Included is a disc on bottom for neutralizing magnet. Powerful magnets are 1 1/8" in dia. and 1 1/8" high.
    B421
    CAD $13.99
    Pre-Order Now
  • MORTISING CHISEL 5/8IN.
    Add to Cart

    MORTISING CHISEL 5/8IN.

    CAD $14.99
    Mortising Chisel for Mortising Attachment. Each chisel is complete with a drill bit. Save time and cost by mortising. Size: 5 / 8" Collar Diameter: 3 / 4"
    B320058
    CAD $14.99
    Add to Cart
  • MORTISING CHISEL 3/8IN.
    Pre-Order Now

    MORTISING CHISEL 3/8IN.

    CAD $12.99
    Mortising Chisel for Mortising Attachment Each chisel is complete with a drill bit. Save time and cost by mortising. Size: 3 / 8" Collar Diameter: 3 / 4"
    B320038
    CAD $12.99
    Pre-Order Now
  • MORTISING CHISEL 1/4IN.
    Add to Cart

    MORTISING CHISEL 1/4IN.

    CAD $12.99
    Mortising Chisel for Mortising Attachment Each chisel is complete with a drill bit. Save time and cost by mortising. Size: 1 / 4" Collar Diameter: 3 / 4"
    B320014
    CAD $12.99
    Add to Cart
  • MORTISING CHISEL 1/2IN.
    Pre-Order Now

    MORTISING CHISEL 1/2IN.

    CAD $12.99
    Mortising Chisel for Mortising Attachment.Each chisel is complete with a drill bit. Save time and cost by mortising. Size: 1 / 2" Collar Diameter: 3 / 4"
    B320012
    CAD $12.99
    Pre-Order Now
  • CHISEL SET 8 PC WOODTURNING
    Pre-Order Now

    CHISEL SET 8 PC WOODTURNING

    CAD $32.99
    B316 8pc Woodturning Chisel Set Quality wood lathe chisel set at a great price! This set includes 8 essential chisels used for turning spindles, pens, bowls and other projects. The 4-1/4" blade is made of high carbon steel, giving years of use and the...
    B316
    CAD $32.99
    Pre-Order Now
  • HOLDER MAG BASE FINE ADJ.
    Add to Cart

    HOLDER MAG BASE FINE ADJ.

    CAD $32.99
    Magnetic Holder With Fine Adjustment Powerful permanent magnet holding power Accepts all standard dials and stems On-off lever quickly releases magnet|
    B303
    CAD $32.99
    Add to Cart
  • DIAL INDICATOR DIGITAL 0 1IN. THREE READING
    Add to Cart

    Igaging

    DIAL INDICATOR DIGITAL 0 1IN. THREE READING

    CAD $58.99
    Digital Indicator This digital indicator replaces the "dial indicator" with advanced and more accurate readings. This unit features 3 way readings in inch, metric and fraction. Other unique features include ABS, HOLD function and Data Output to PC...
    B2872
    CAD $58.99
    Add to Cart
  • HEIGHT GAUGE DIGITAL
    Add to Cart

    Igaging

    HEIGHT GAUGE DIGITAL

    CAD $74.99
    Digital Height Gauge This large LCD display Stainless Steel Digital Height gauge has many features not found on other height gauges. First the strong magnets on the base allow for easy setting on steel table tops and fence sides. The unit allows for 2D...
    B2868
    CAD $74.99
    Add to Cart
  • WING COMPASS 8
    Add to Cart

    Groz

    8IN. WING COMPASS

    CAD $14.99
    8" Wing Compass - Groz This rugged industrial grade compass is manufactured from heavy gauge steel with an attractive black powder coated finish. The tip is accurately ground. Heavy Duty hinge and knurled locking nut help in convenient movement. Used...
    B2772
    CAD $14.99
    Add to Cart
  • AUTO PUNCH AND MAGNETIC SCRIBER
    Add to Cart

    AUTO PUNCH AND MAGNETIC SCRIBER

    CAD $12.99
    Auto Punch & Magnetic Scriber The Scriber is carbide tipped for longer life & has clear markings on materials such as hardened steel, glass & ceramics. There is a permanent alinico magnet on the head for picking up small parts which is very...
    B2714
    CAD $12.99
    Add to Cart
  • ELECTRONIC EDGE FNDER
    Add to Cart

    Groz

    ELECTRONIC EDGE FINDER

    CAD $56.99
    Electronic Edge Finder - GROZ This edge finder is an accurate and time saving tool for precisely locating work edges, shoulders, grooves etc. Ideal for use on both conventional and CNC equipment. The edge finder lights up instantly when the stylus...
    B2700
    CAD $56.99
    Add to Cart
  • SPOKESHAVE ROUND SOLE
    Add to Cart

    SPOKESHAVE ROUND SOLE

    CAD $22.99
    Spokeshave Round Sole A tool that every shop should have. They are great for shaping tool handles, spindles, or pattern making anything that can be shaped freehand. Made of cast iron with steel blades having vertical and lateral adjustments Total length...
    B2669R
    CAD $22.99
    Add to Cart
  • SPOKESHAVE FLAT SOLE
    Add to Cart

    SPOKESHAVE FLAT SOLE

    CAD $22.99
    Spokeshave Flat Sole A tool that every shop should have. They are great for shaping tool handles, spindles, or pattern making anything that can be shaped freehand. Made of cast iron with steel blades having vertical and lateral adjustments Total length...
    B2669F
    CAD $22.99
    Add to Cart
  • FILE AND RASP SET 17PCS WITH CARRY CASE
    Add to Cart

    FILE AND RASP SET 17PCS WITH CARRY CASE

    CAD $36.99
    17 pc File & Rasp Set with Canvas Carrying Pouch These selected Files feature an ergonomic rubberized soft grip handle, specially selected heat treat alloy steel construction and overall high quality for demanding applications. Contains 10" Mill...
    B2643
    CAD $36.99
    Add to Cart
  • FILE ROUND 10IN.
    Add to Cart

    FILE ROUND 10IN.

    Now: CAD $4.99
    Was: $5.99
    B2642 Round File, 10" These selected Files feature an ergonomic rubberized soft grip handle, specially selected heat treat alloy steel construction and overall high quality for demanding applications.
    B2642
    Now: CAD $4.99
    Was: $5.99
    Add to Cart
  • FILE FLAT 10IN.
    Add to Cart

    FILE FLAT 10IN.

    Now: CAD $6.99
    Was: $7.99
    B2640 Flat File 10" These selected Files feature an ergonomic rubberized soft grip handle, specially selected heat treat alloy steel construction and overall high quality for demanding applications.
    B2640
    Now: CAD $6.99
    Was: $7.99
    Add to Cart

Subscribe to our newsletter

Sign up to our newsletter to get the latest updates on new products and upcoming sales delivered to your inbox. We respect your privacy, we will never share or sell your email.

WHY SHOP WITH US
QUALITY STAFF
ESTABLISHED 1976
100% CANADIAN
ACROSS CANADA
BUY DIRECT & SAVE
Crown Lubricants
DeWalt
Stanley